wp725_zip.exe P-Sea WindPlot II 7.25.18 Update only 2/6/2012
wp3D723_zip.exe P-Sea WindPlot II 3D 7.23.25 Update only 3/25/2011 (must do 7.24 full install if want newer)
wp725max_zip.exe P-Sea WindPlot MAX (C-Map) 3D 7.25.18 Update only 2/6/2012
wp3D723max_zip.exe P-Sea WindPlot MAX 3D (C-Map) 7.23.26 Update only 3/25/2011
(must do 7.25.1 full install if want new version)
Sounder_zip.exe P-Sea Sounder Stand-Alone Ver. 7.25.1 Update only 9/23/2011
What is new in 7.25
Added: Two new check boxs in Chg/COM setup. One turns the flashing asterisk off of lattitude and FAST MODE for improved data flow.
Added: Fast COM in COM adjust window when GPS data is streaming slowly or boat is lagging.
Added: Right-Click touch button to turn touch mode off
Added: Right click Range button to turn touch mode ON
Added: Programable range buttons: Right-Click mini-range buttons to program each button for a specific range
Added: Right-Click DELETE MARK button on cursor box to delete all marks that are being displayed on the screen.
Added: 3D: Upper depth alarm show red line & bottom alarm shows a green line on the 3D screen.
Added: AIS: maximum targets displayed can be set for tracking more than the default 50.
Added: Warning box on AIS CPA need tracking on with durations 10 seconds (Required for CPA)
Added: AIS targets can appear in mini-chart window
Added: Navionics charts 2011 or newer on CF memory cards no longer need a special Navionics card reader
(Internet required for first time activation on new chart cards.
Added: ALWAYS ON to pop-up button control
Added: More choices for where heading comes from in Mag.Variation adjustment
FIX: AIS: HIDE column now hides entire target or just the trail.
FIX: 3D: Fixed making Low Res World charts.
FIX: Automated FREE NOAA BSB chart download. Just unzip downloaded BSB chart BSB_ROOT folder to hardrive and start WindPlot 7.25.16
FIX: Disable system model mode add NSM to command line of WindPlot start up icon WndPltII.EXe.
FIX: Fix default position of chart installer list.
FIX: Windows 7 beeping sounds on alarms and other functions fixed.
FIX: Some skewed charts caused skewed chart display to turn off.
FIX: TTM output NMEA183 sentence not sending time and added check sum.
FIX: Computer locks when loading BSB charts a certian way.
FIX: AIS tracks match when using larger Windows print.
FIX: AIS clear all targets from list didn't work.
FIX: AIS list now shows total time tracked
FIX: Spanning P-Sea FishFinder would not display
FIX: Reworked Sidebar data split screen so works right on all Windows Font Sizes.
FIX: Not moving warning is not so sensitive now.
FIX: Mark Search & Add will now look for regular, 32 bit and compressed marks all at the same time.
FIX: Some message boxes would cause 7.25.9 to lock up
FIX: Err in 7.25.7 would not show all of Magnetic Variation window.
FIX: Change mark from screen would alter marks position
FIX: Load boundaries had issues.
FIX: COM ports not working sometimes on new install but ver.7.23 would work. Reloaded COM software from 7.23 into 7.25
FIX: Navionics charts would say DLL not found.
FIX: AIS CPA alarm would not sound off.
FIX: COM window would resize when setting baud or COM#
FIX: P-Sea Vector chart loader set so searchs sub folders.
FIX: Fixed radar option so Eithernet is first choice on new installs
FIX: Fixed DUAL PLOT "Now Trawl Plot" in COM window so works with Simrad net sensor position
FIX: 3D offset too high would cause 3D picture not to display
FIX: 3D change 3D folder from default and 3D would not remember the change.
FIX: AIS had issues when tracks were turned off
ASF ACTIVATION When this 7.23/7.25 update is installed you should see a "USE ASF" check box on the TD calibration box and in the TD to LL converter located in the OPTIONS menu. Just check this and it will ask for an activation code. Purchase the code and enter it here. Then, you will be using ASF when the box is checked and using your old calibrations when it is not checked. Compare them now before Loran-C is shut down.. We believe the ASF corrections to be almost as close as the calibrated values for working offshore (NOTE: Errors will incease in ASF corrections as you get close to land.)
ERROR MESSAGE > "OUTPUT FILE COULD NOT BE CREATED" If you get this message then you need to open "My COMPUTER" and view the files on the "C" drive. Find the PC-PLOTT folder and right-click on it, select "PROPERTIES", un-check the "READ ONLY" box and click on "APPLY". Then try unzipping the files, it should work now.